How to Install a Bathtub ( Guide).
How to Install a Bathtub ( Guide).
Blog Article
The article below relating to How to Install a Bathtub is relatively motivating. Don't skip it.
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably hard job. If the old bathtub is conveniently obtainable, the job can move rapidly; if you need to open a wall to eliminate the old tub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the brand-new one. Make certain you have qualified on your own for the work and also are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and also product list must consist of the following:
Planning for the Installment
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the tub in the needed position. The wooden boards are handy in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and also inspect all joints as well as new pipework for leakages as well as tighten them if required. Load the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has been utilized at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former type must be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that excerpt was really helpful. Make sure you take a moment to distribute this blog if you enjoyed it. Thanks for going through it.
Book Instantly Report this page